NSE6_FSW-7.2 Practice Exam Tests Latest Updated on Dec-2025
Pass NSE6_FSW-7.2 Exam in First Attempt Guaranteed Dumps!
The Fortinet NSE 6 - FortiSwitch 7.2 certification exam covers a wide range of topics, including FortiSwitch hardware and software architecture, VLAN configuration, Spanning Tree Protocol (STP), link aggregation, and multicast routing. Candidates will also be tested on their ability to configure FortiSwitch security features, such as access control policies, port security, and network segmentation. NSE6_FSW-7.2 exam consists of multiple-choice questions and simulations, and passing the exam requires a deep understanding of FortiSwitch technologies and their practical applications in real-world scenarios.
Fortinet NSE6_FSW-7.2 certification is an important credential for network security professionals who work with Fortinet’s FortiSwitch products. It demonstrates the candidate’s expertise in deploying, configuring, and managing secure networks using Fortinet’s technology. Holding this certification can help professionals to advance their careers and increase their earning potential.
Fortinet NSE6_FSW-7.2 Certification Exam is designed for network security professionals who specialize in Fortinet's FortiSwitch platform. Fortinet NSE 6 - FortiSwitch 7.2 certification validates the skills and knowledge required to configure, administer, and troubleshoot FortiSwitch products in a network environment. NSE6_FSW-7.2 exam covers a wide range of topics, including VLANs, link aggregation, spanning tree protocol, and access control lists, ensuring that certified professionals are well-versed in all aspects of FortiSwitch deployment.
NEW QUESTION # 19
Refer to the exhibits
Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)
- A. Add the MAC address of PCI as a member of VLAN 10.
- B. Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.
- C. Add VLAN ID 10 as a member of the untagged VLANs on port1.
- D. Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.
Answer: A,C
NEW QUESTION # 20
How are the 'by VLAN redirect MAC address quarantine' mode and the 'by redirect MAC address quarantine' mode on FortiGate similar?
- A. Both modes block intra-VLAN traffic by FortiGate automatically.
- B. Both modes add quarantined device MAC addresses to the blocked firewall address group.
- C. Both modes move quarantined devices to the quarantine VLAN.
- D. Both modes require firewall policies to block inter-VLAN traffic.
Answer: A
NEW QUESTION # 21
An administrator needs to deploy managed FortiSwitch devices in a remote location where multiple VLANs must be utilized to segment devices. No Layer 3 switch or router is present. The the only WAN connectivity is the router provided by the ISP connected to the public internet.
Which two items will the administrator need to use? (Choose two.)
- A. A FortiSwitch interface connected to the ISP router configured with fortilink-13-mode enabled.
- B. FortiSwitch devices that have the required internal hardware for this configuration.
- C. FortiSwitch and FortiGate devices configured with VXLAN interfaces.
- D. FortiSwitch and FortiGate devices configured with IPsec interfaces.
- E. FortiSwitch devices configured with NAT disabled.
Answer: A,E
Explanation:
To deploy FortiSwitch in a remote location with multiple VLANs and no Layer 3 switch or router, you would need specific configurations:
VXLAN Interfaces (B):
Purpose: VXLAN (Virtual Extensible LAN) allows network segmentation without a Layer 3 device, extending VLAN capabilities across dispersed geographical locations over the WAN.
Implementation: Configuring VXLAN on both FortiSwitch and FortiGate can encapsulate Layer 2 traffic over a Layer 3 network, making it ideal for scenarios lacking dedicated routing hardware.
Appropriate Hardware (D):
Requirement: Not all FortiSwitch models might support advanced features like VXLAN; hence, ensuring that the hardware can support such configurations is crucial.
Reference:
For specific information on VXLAN configuration and hardware requirements, refer to the technical documentation provided by Fortinet: Fortinet Product Documentation
NEW QUESTION # 22
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?
- A. FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.
- B. Use a migration tool based on Python script to convert the configuration.
- C. Register FortiSwitch to FortiSwitch Cloud to save a copy before managing with FortiGate.
- D. Enable the FortiLink setting on FortiSwitch before the authorization process.
Answer: A
Explanation:
When transitioning the management of a FortiSwitch from standalone mode to being managed by FortiGate via FortiLink, it is critical to ensure that the existing configurations are preserved. The best practice involves:
FortiGate's Role in Configuration Preservation:
FortiGate has the capability to automatically preserve the existing configuration of a FortiSwitch when it is integrated into the network via FortiLink. This feature helps ensure that the transition does not disrupt the network's operational settings.
Configuration Integration:
As FortiSwitch is integrated into FortiGate's management via FortiLink, FortiGate captures and integrates the existing switch configuration, enabling a seamless transition. This process involves FortiGate recognizing the FortiSwitch and its current setup, then incorporating these settings into the centralized management interface without the need for manual reconfiguration or the use of additional tools.
Reference:
For further details on managing FortiSwitch with FortiGate and the capabilities of FortiLink, consult the FortiSwitch and FortiGate integration guide available on: Fortinet Product Documentation
NEW QUESTION # 23
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?
- A. The native VLAN is implicitly part of the allowed VLAN on the port.
- B. Allowed VLANS expand the collision domain to the port.
- C. FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.
- D. Untagged VLANs must be part of the allowed VLANs: ingress and egress.
Answer: A
NEW QUESTION # 24
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The port full speed prior the split was 100G SFP+
- B. The split port can be assigned to native VLAN
- C. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
- D. The FortiSwitch model is equipped with a maximum of 54 interfaces.
Answer: A,C
Explanation:
Regarding the configuration of a FortiSwitch to split a port into multiple smaller interfaces:
The CLI commands are enabling a split port into four 10Gbps interfaces (Option B): The command shown in the exhibit is typically used to configure a high-speed port (like a 40Gbps or 100Gbps interface) to be divided into smaller, independent 10Gbps interfaces. This feature allows more flexible use of the switch's physical resources.
The port full speed prior to the split was 100G SFP+ (Option C): Given the context of splitting the port into multiple 10Gbps interfaces, the original port configuration likely supported a high-speed transceiver such as 100G SFP+. This would make it technically feasible to divide the interface into multiple 10Gbps channels, enhancing connectivity options without requiring additional physical interfaces.
These configurations and capabilities are typical in modern network setups, especially in environments requiring high density and flexibility in connectivity, allowing network administrators to optimize physical infrastructure efficiently.
NEW QUESTION # 25
What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?
- A. FortiGate managing FortiSwitch
- B. HA backup FortiGate managing FortiSwitch
- C. POE with high density FortiSwitch
- D. FortiSwitch functioning as standalone
Answer: A
Explanation:
In a hierarchical network model, the role of a device functioning simultaneously as both the distribution and core is most accurately described as "FortiGate managing FortiSwitch (B)." In this setup, FortiGate acts as the central unit managing multiple FortiSwitch units, thereby functioning both as a distribution layer-handling traffic between network segments-and as a core layer-managing traffic within the network on a broader scale. This setup is typical in medium-sized networks where a single device is capable enough to handle both roles effectively.
NEW QUESTION # 26
Which two statements about the FortiLink authorization process are true? (Choose two.)
- A. FortiSwitch requires a reboot to complete the authorization process.
- B. FortiLink authorization sets the FortiSwitch management mode to FortiLink.
- C. The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.
- D. A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.
Answer: B,D
Explanation:
The FortiLink authorization process is an integral part of setting up FortiSwitch to be managed by FortiGate. The correct statements regarding the FortiLink authorization process are:
C . A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization. This is a part of the FortiLink protocol, where FortiGate communicates with the connected FortiSwitch to establish management and control. This frame initiates the configuration and management process, allowing FortiGate to effectively control the switch.
D . FortiLink authorization sets the FortiSwitch management mode to FortiLink. Once authorized, the management mode of FortiSwitch is set to FortiLink, indicating that it is being managed via a FortiLink connection from a FortiGate appliance. This changes the operational mode of the switch to be under the control of the FortiGate for centralized management and policy application.
Reference:
Further details on the FortiLink setup and authorization process can be accessed through the FortiGate configuration guides available on the Fortinet Documentation site.
NEW QUESTION # 27
Refer to the exhibit.
Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?
- A. port1 on Core-2 is discarding only management traffic.
- B. Core-2 has the lowest bridge priority.
- C. Core-1 and Core-2 do not have MCLAG configuration.
- D. Access-1 is the root bridge and can only have one root port.
Answer: C
NEW QUESTION # 28
Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?
- A. Location
- B. Power management
- C. Inventory management
- D. Network policy
Answer: C
NEW QUESTION # 29
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?
- A. The native VLAN is implicitly part of the allowed VLAN on the port.
- B. Allowed VLANS expand the collision domain to the port.
- C. FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.
- D. Untagged VLANs must be part of the allowed VLANs: ingress and egress.
Answer: A
Explanation:
The native VLAN is implicitly part of the allowed VLAN on the port (C): On a managed FortiSwitch port, the native VLAN, which is the VLAN assigned to untagged traffic, is implicitly included in the list of allowed VLANs. This means it does not need to be explicitly specified when configuring VLAN settings on the port. This configuration simplifies VLAN management and ensures that untagged traffic is handled correctly without additional configuration steps.
NEW QUESTION # 30
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
- A. Physical interfaces
- B. Switch virtual interfaces
- C. Detected management interfaces
- D. Loopback interfaces
Answer: B,D
Explanation:
In dynamic routing on FortiSwitch, certain types of interfaces are utilized to participate in the routing processes. The types of interfaces that can be used include:
Loopback Interfaces (B):
Loopback interfaces are virtual interfaces that are always up, making them ideal for use in routing protocols where a stable interface is necessary. They are commonly used to establish router IDs and manage routing information more reliably.
Switch Virtual Interfaces (C):
Switch Virtual Interfaces (SVIs) are assigned to VLANs and can have IP addresses assigned to them, making them capable of participating in Layer 3 routing. SVIs are essential for routing between different VLANs on a switch and can participate in dynamic routing protocols to advertise networks or make routing decisions.
Physical Interfaces (D) and Detected Management Interfaces (A) are not typically used directly by dynamic routing protocols for their operations in the context of FortiSwitch.
Reference:
For more information on how these interfaces interact with dynamic routing protocols, you can check the FortiSwitch documentation on Fortinet's official documentation site: Fortinet Product Documentation
NEW QUESTION # 31
Exhibit.
port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)
- A. You must add port24 native VLAN as an allowed VLAN on internal.
- B. You must add VLAN ID 200 to the allowed VLANS on internal.
- C. You must allow VLAN ID 4094 on port24, if management traffic is tagged.
- D. You should use VLAN ID 4094 as the native VLAN on port24.
Answer: C,D
NEW QUESTION # 32
Exhibit.
Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)
- A. These two routes are available in the hardware routing table.
- B. These two routes will be used as load-balancing routes.
- C. These two routes have a higher administrative distance value available to the destina-tion networks.
- D. These two routes will become primary, if the best routes are removed.
Answer: C,D
NEW QUESTION # 33
Exhibit.
You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.
- A. The FortiSwitch device is scheduled to reboot as part the authorization process
- B. The system time is not in-sync and is using a non-default value
- C. The management mode was set to use FortiLink mode.
- D. Switch auto-discovery is enabled.
Answer: C
NEW QUESTION # 34
Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?
- A. Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.
- B. FortiSwitch uses only the Ethernet type to assign traffic to VLANs.
- C. It provides benefits that can be obtained when using 802.1X authentication.
- D. lt is a scalable and secure solution in comparison to other Layer 2 security measures.
Answer: C
Explanation:
It provides benefits that can be obtained when using 802.1X authentication (C): MAC, IP, and protocol-based VLANs on FortiSwitch are beneficial in network environments where additional granularity is needed in traffic segmentation and security, similar to what can be achieved through 802.1X authentication. These VLAN types allow for dynamic assignment of ports to VLANs based on the characteristics of the incoming traffic, enhancing both security and network efficiency.
NEW QUESTION # 35
What type of multimode transceiver can be used to split a 40G port?
- A. SFP+ transceiver
- B. SFP transceiver
- C. QSFP transceiver
- D. QSFP+ transceiver
Answer: D
NEW QUESTION # 36
What type of multimode transceiver can be used to split a 40G port?
- A. SFP+ transceiver
- B. SFP transceiver
- C. QSFP transceiver
- D. QSFP+ transceiver
Answer: D
Explanation:
QSFP+ transceiver (A): The QSFP+ (Quad Small Form-factor Pluggable Plus) transceiver is designed to handle 40G data rates and can be used to split a 40G port into multiple 10G connections. This type of transceiver supports such configurations, making it suitable for high-density applications where multiple 10G connections are derived from a single 40G port, thereby maximizing the utilization of the port and the fiber infrastructure.
NEW QUESTION # 37
Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)
- A. switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.
- B. By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.
- C. Settings related to DHCP option 82 are only configurable through the CLI
- D. Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.
Answer: A,C
Explanation:
Switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks (B): This feature of DHCP snooping helps prevent DHCP exhaustion attacks by ensuring that the destination MAC addresses in DHCP packets match the MAC addresses learned by the switch. This check helps prevent attackers from overwhelming the DHCP server with requests from spoofed MAC addresses.
Settings related to DHCP option 82 are only configurable through the CLI (D): DHCP Option 82 is used for "agent information," and it's typically used in network environments where additional information between DHCP clients and servers is necessary for policy and billing purposes. Configuration of these settings in FortiSwitch is only available through the Command Line Interface (CLI), not the Graphical User Interface (GUI).
NEW QUESTION # 38
Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?
- A. Enable IGMP snooping proxy.
- B. Enable the IGMP flood setting on the static port for all multicast groups.
- C. Enable the IGMP flood reports setting on the mRouter port.
- D. Enable IGMP flood unknown multicast traffic on the global setting.
Answer: A
NEW QUESTION # 39
Which two statements about managing a FortiSwitch stack on FortiGate are true? (Choose two.)
- A. Only a hardware-based FortiGate can manage a FortiSwitch stack.
- B. A FortiLink interface must be enabled on FortiGate.
- C. FortiSwitch must be operating in standalone mode before authorization.
- D. The switch controller feature must be enabled on FortiGate.
Answer: B,D
NEW QUESTION # 40
......
NSE 6 Network Security Specialist Free Certification Exam Material from PassTestking with 57 Questions: https://www.passtestking.com/Fortinet/NSE6_FSW-7.2-practice-exam-dumps.html
NSE6_FSW-7.2 Dumps Full Questions - Exam Study Guide: https://drive.google.com/open?id=1HrGtty_BV1rikZSyMlBntiB3S5KJ_wDa