200-601 by Cisco Actual Free Exam Q&As

Question 1

Refer to the exhibit.

An expansion project added an E-Tap and Device Level Ring to interface FastEthernet1/1 of L2SW1. The administrator has looked at the logs of L2SW1 and found that
FastEthernet1/1 was in an error-disabled state.Using command line access on L2SW1, the administrator issued the following commands in configuration mode:
L2SW1(config)# interface FastEthernet 1/1
L2SW1(config-if)# shutdown
L2SW1(config-if)# no shutdown
The administrator checked the logs of L2SW1 and found the following:
Mar 30 02:23:17.588: %PM-4-ERR_DISABLE: bpduguard error detected on Fa1/1, putting
Fa1/1 in err-disable state
The administrator checked the software configuration of the switch port and found the following:
interface FastEthernet1/1
switchport access vlan 310
switchport mode access
speed 100
duplex full
no mdix auto
spanning-tree portfast
spanning-tree bpduguard enable
Why has the port gone error-disabled?

A. Automatic MDI Crossover detection is disabled. B. There is a duplex mismatch between interface FastEthernet1/1 and the E-Tap. C. The E-Tap is configured at 10Mbps and the switch port is configured at 100Mbps. D. interface FastEthernet1/1 is configured as an access port on the wrong VLAN. E. The E-Tap is not configured as a ring supervisor causing a loop on interface FastEthernet1/1.

Discussion 0

Correct Answer: E Vote an answer

Question 2

Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?

A. CIP Motion requires a star topology which is not supported by REP. RPVST+ is a suitable resiliency protocol for CIP motion. B. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion. C. REP convergence is not fast enough. RPVST+ is a suitable resiliency protocol for CIP motion. D. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion.

Discussion 0

Correct Answer: D Vote an answer

Question 3

Refer to the exhibit.

What issue does this topology present for the represented traffic flow?

A. I/O control traffic should utilize the 2.4 GHz band based on best practices. B. Only one of the Work Group Bridges can transmit at a time, because 802.11 is half duplex. C. The Converged Plant-wide Ethernet best practices for 802.11 wireless don't allow for
PAC to PAC traffic. D. Standard Produce/Consume traffic is not suitable for an 802.11 wireless environment.

Discussion 0

Correct Answer: B Vote an answer

Question 4

What can be done to increase the security in depth in an industrial zone?

A. Place a 'data diode' in front of the IDS server B. Create a high availability solution for the IDS server C. Add specific SCADA signatures to the IDS server D. Add additional disk storage to the IDS server

Discussion 0

Correct Answer: C Vote an answer

Question 5

Profinet has been disabled on a Cisco Industrial Ethernet switch, which CLI commands correctly enable ProfiNET on VLAN 10?

A. switch(config)#profinet
switch(config)#profinet vlan 10 B. switch#enable profinet
switch(config)#vlan 10
switch(config-vlan)#profinet C. switch#enable profinet
switch(config)#profinet vlan 10 D. switch(config)#profinet
switch(config)#vlan 10
switch(config-vlan)#profinet

Discussion 0

Correct Answer: A Vote an answer

Question 6

You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch that was deployed using the Express Setup. Which CLI command will increase the number of available IPv4 IGMP groups and multicast routes from 256 to 1000 on this switch?

A. switch(config)#sdm prefer vlan igmp B. switch(config)#sdm prefer routing igmp C. switch(config)#sdm prefer routing D. switch(config)#sdm prefer vlan

Discussion 0

Correct Answer: C Vote an answer

Question 7

A ProfiNET management system operator is unable to add a ProfiNET Conformance Class
B device to a SIMATIC management station. The device is connected to interface
FastEthernet1/3. Based on the provided CLI output, which statement is correct? switch#show profinet lldp
Fa1/1 port-003-00000 On
Fa1/2 port-004-00000 On
Fa1/3 port-005-00000 Off
Fa1/4 port-006-00000 Off
Fa1/5 port-007-00000 On
Fa1/6 port-008-00000 Off
Fa1/7 port-009-00000 On
Fa1/8 port-010-00000 Off

A. The port label needs to be changed on interface FastEthernet 1/3 to "port-003-00000" B. The connected device is not sending LLDP packets with ProfiNET extensions C. ProfiNET is disabled on this switch D. LLDP has been disabled on this switch

Discussion 0

Correct Answer: B Vote an answer

Question 8

A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency?
(Choose two)

A. DLR is designed for single network operation at the machine level B. Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure C. Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control D. Half of the network traffic goes clockwise on the ring and the other half counter- clockwise, reducing by 50% the impact of cable failure E. DLR is the only resiliency technology that is supported by CIP Safety

Discussion 0

Correct Answer: A,C Vote an answer

Question 9

What is the purpose of Spanning Tree Protocol?

A. to enhance the functions of SNMP B. to maintain a loop-free Layer 2 network topology C. to provide multiple gateways for hosts D. to prevent routing loops E. to create a default route

Discussion 0

Correct Answer: B Vote an answer

Cisco Managing Industrial Networks for Manufacturing with Cisco Technologies - 200-601 Exam Practice Test