Free NACE NACE-CIP1-001 Study Guides Exam Questions and Answer
NACE-CIP1-001 Exam Dumps, NACE-CIP1-001 Practice Test Questions
Do you know how difficult the NACE CIP1-001 certification is to write?
NACE CIP1-001 certification is a difficult exam. The reason behind this is the wide range of topics covered in the exam. The topics are related to the chemical, physical and biological properties of the coatings. You have to be familiar with these properties. The candidates need to prepare for the NACE CIP1-001 test. They can easily download the NACE CIP1-001 exam dumps. The exam dumps contain different kinds of questions that help the candidates to easily pass the NACE CIP1-001 exam. Questions and answers help you to easily prepare for the NACE CIP1-001 exam. A score report helps you to know how much time is required for your preparation. It is very helpful for the candidates to plan their time. Decide the location where you want to sit for the exam. Accurate and concise questions will help you to easily pass the NACE CIP1-001 exam.
The salary of a NACE CIP1-001 certified professional can be found here.
The Average salary of different countries of NACE CIP1-001 Certified professionals is given below:
- UK 49527.40 Pounds
- USA 67,000 USD
- India 4982421.50 INR
NEW QUESTION 28
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Presence of weld spatter may produce a false positive
- C. Synthetic oil or grease may not be identified
- D. Chloride salt may produce a false positive
Answer: C
NEW QUESTION 29
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 2.5 cm (1 inch)
- C. 2.5 millimeters (.10 inch)
- D. 1 cm (.39 inch)
Answer: B
NEW QUESTION 30
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. The inspector's personal opinions of the application team
- C. Subjective comments re ding the application team
- D. Objective comments regarding the application work
Answer: A
NEW QUESTION 31
A successful coating inspector must be able to
- A. apply the coating with expert accuracy.
- B. look for problems or issues during application.
- C. advise the coating applicator on how to mix the coating.
- D. recommend the appropriate coating technique for the job to the contractor.
Answer: B
NEW QUESTION 32
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Surface Conditions E-G
- C. Rust Grades A-D
- D. Rust Grades 1-4
Answer: C
NEW QUESTION 33
Dew point is the temperature at which
- A. the air is saturated.
- B. condensation occurs.
- C. humidity decreases
- D. water freezes.
Answer: B
NEW QUESTION 34
Which is a component that supplies most of the features and functions of the material?
- A. pigment
- B. binder
- C. solvent
- D. additive
Answer: B
NEW QUESTION 35
Conventional spray is a good choice when:
- A. High quality finishes are required
- B. High production rates are required
- C. High viscosity coatings are being applied
- D. High transfer efficiency is required
Answer: A
NEW QUESTION 36
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A general guide
- B. A method to grade surface profile
- C. Pass/fail criteria
- D. A final conflict resolution method
Answer: A
NEW QUESTION 37
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
Answer: C
NEW QUESTION 38
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 4
- C. Level 1
- D. Level 2
Answer: A
NEW QUESTION 39
Removal of welds splatter is required:
- A. When ISO abrasive blast standards are specified
- B. When NACE/SSPC abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION 40
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Failing to determine the base metal reading (BMR)
- C. Taking measurements too far from the edge of a surface
- D. Measuring ditty, tacky, or soft films
Answer: A,B,D
NEW QUESTION 41
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Hand tools
- C. Abrasive blast nozzles
- D. Airless spray equipment
Answer: A
NEW QUESTION 42
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Inspection personnel
- C. The Owner's personnel
- D. The Application personnel
Answer: A
NEW QUESTION 43
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Using a damaged gauge
- B. Dragging a gauge through wet coating
- C. Placing the gauge along the longitudinal axis
Answer: A,B
NEW QUESTION 44
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. direct and perform the work stated in the specification.
- C. observe and direct the work of the contractors.
- D. observe and report the quality of the work performed.
Answer: D
NEW QUESTION 45
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Bring the matter up at the pre-job conference
- C. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
Answer: B
NEW QUESTION 46
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. inhibitor residues
- B. grease and oil
- C. soluble chemical salts
- D. sulfates
Answer: B
NEW QUESTION 47
......
The topics of the NACE CIP1-001 Exam are discussed here
- Maintenance personnel
- Coating manufacturers and technical sales representatives
- Quality assurance/control managers
Latest NACE-CIP1-001 Actual Free Exam Questions Updated 100 Questions: https://www.passtestking.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
Attested NACE-CIP1-001 Dumps PDF Resource [2022]: https://drive.google.com/open?id=1rVNpw7_91BYTanNZaXedrOy8gnNdoRdG