C_IBP_2005 by SAP Actual Free Exam Q&As

Question 1

Which forecasting algorithms leverage the SAP HANA Predictive Analysis Library?
There are 3 correct answers to this question.
Response:

A. Demand Sensing B. Pre-Processing C. Best Model Selection D. Time-Series E. Accuracy Measurements

Discussion 0

Correct Answer: A,B,C Vote an answer

Question 2

Which of the following checks for master data and key figures does the Check Mode algorithm trigger?
There are 3 correct answers to this question.
Response:

A. Checks whether the location products specified in the master data are connected by customer sourcing rules within the supply chain network. B. Checks whether the required planning level master data exists for a subset of input key figures. C. Checks whether the location resource specified in the master data form a cycle in the supply chain network. D. Checks whether the sourcing in the Production Source Item Master Data type exists. E. Checks whether the heuristic detects cycles formed by nodes (such as location products) in the supply chain network.

Discussion 0

Correct Answer: A,B,E Vote an answer

Question 3

You need to create various planning operators. Which operators must you assign to your planning area to view them in Microsoft Excel?
There are 2 correct answers to this question.
Response:

A. Check Mode Operator B. Statistical Forecasting C. Disaggregation Operator D. Copy Operator

Discussion 0

Correct Answer: B,C Vote an answer

Question 4

What are some of the prerequisites for configuring a planning area that results in a successful consistency check?
There are 2 correct answers to this question.
Response:

A. Configure at least one calculated key figure for the planning area. B. Configure at most two input key figures on the same planning level in a key figure calculation. C. Assignment of a compound master data type necessitates the assignment of its component master data types too. D. Specify a planning horizon in the planning area for each level of the assigned time profile.

Discussion 0

Correct Answer: C,D Vote an answer

Question 5

Which of these conditions must be met to create a Local Member key figure?
Please choose the correct answer.
Response:

A. Use Excel Cell References in Report Editor is selected B. Key Figure is created in the Planning Area app C. Key Figure is selected in the Key Figures tab in Excel add-on D. Activate Local Member Recognition is selected

Discussion 0

Correct Answer: D Vote an answer

Question 6

You create an S&OP operator for heuristics on an SAP IBP project. What must you enable for the S&OP operator which is specifically relevant for sub networks?
Please choose the correct answer.
Response:

A. Node-Based isolation check B. Compute Expected Supply parameter C. Normalize Quotas parameter D. Balance Receipts parameter

Discussion 0

Correct Answer: B Vote an answer

Question 7

Which of the following fields can be overwritten in the New Planning view by fixed default value settings?
There are 3 correct answers to this question.
Response:

A. Language B. Planning Unit C. Default Display Time D. Currency to ID E. Unit of Measure to ID

Discussion 0

Correct Answer: B,D,E Vote an answer

Question 8

You have set up a planning area and data is available. You adjust the necessary time profile settings and run the consistency check.
Which settings can you change and still run a successful consistency check?
There are 2 correct answers to this question.
Response:

A. Change the description of the attributes in a time profile. B. Remove an attribute assigned to the time profile level if the attribute is used in a planning level. C. Add a new time profile level to the time profile. D. Change the past and future horizon of the levels in the time profile.

Discussion 0

Correct Answer: A,D Vote an answer

Question 9

Which of the following combination of nodes can be connected using the C-rule and T-rule sourcing rules?
Please choose the correct answer.
Response:

A. Plant-Supplier and Customer-Supplier B. Customer-Warehouse and Warehouse-Plant C. Warehouse-Warehouse and Warehouse-Plant D. Customer-Plant and Warehouse-Supplier

Discussion 0

Correct Answer: D Vote an answer

SAP Certified Application Associate - SAP Integrated Business Planning - C_IBP_2005 Exam Practice Test