CWDP-305 by CWNP Actual Free Exam Q&As

Question 1

In high-density environments, such as stadiums and convention centers, what extra factor has to be taken into account that can attenuate Wi-Fi signals when these environments are having an event?

A. Fire doors B. Thick walls C. I-Beams D. People

Discussion 0

Correct Answer: D Vote an answer

Question 2

What are three potential benefits when an organization lets their employees bring their own device onto the company s network"?

A. increased security Enhanced productivity, and Decreased attack surface B. Enhanced productivity Increased costs, and Decreased satisfaction C. Enhanced productivity. Increased costs, and Increased satisfaction D. Enhanced productivity Decreased costs and Increased satisfaction

Discussion 0

Correct Answer: D Vote an answer

Question 3

Even when a full pre-design site survey is not performed, what is always recommended to be performed within the deployment areas?

A. An AP-on-a-stick survey of 37% of the facility as this amount provides all of the statistical information required for good design B. A scan in the Sub-i GHz bands to determine If sideband interference will impact 2 4 GHz operations C. A spectrum analysis walkthrough D. A scan m the 5 GHz band looking for common loT interferes

Discussion 0

Correct Answer: C Vote an answer

Question 4

What commonly causes a client-to-AP link imbalance?

A. The client's antenna gain is lower than the AP's antenna gain B. The AP's antenna gain is lower than the client's antenna gain C. The client's transmit power is significantly lower than the AP's transmit power D. The AP's transmit power is significantly lower than the client's transmit power

Discussion 0

Correct Answer: C Vote an answer

Question 5

What statement is true of a WLAN design that supports Real-Time Location Services (RTLS) with 802.11 RFID asset tags?

A. Passive tags do not communicate directly with the WLAN infrastructure, but instead they rely on the tag reader to communicate tag information to the B. With passive tags, AP transmit gain should be increased to supply extra power for near-field coupling or backscatter modulation from the tag to the AP since the passive tag lacks an internal power source. C. Active RFID tags periodically transmit 802.11 beacon management frames that must be synchronized with the AP for proper location of the tagged asset. D. When passive tags are implemented, the AP density should be increased by 25% to make up for the shorter transmit range of passive tags as compared to active tags.

Discussion 0

Correct Answer: A Vote an answer

Question 6

To ensure that your design meets the requirements of the WLAN, what should be defined in your WLAN design software that will result in different requirements at varying locations on the floor plan1?

A. Cable runs B. Requirement areas C. Heatmap colors D. Project name

Discussion 0

Correct Answer: B Vote an answer

Question 7

During a validation site survey, you realize that the installers mounted some of the APs above the ceiling. They said that this was a request from the building architect due to aesthetics constraints.
During the requirements gathering, you weren't advised about any aesthetics constraints from the main stakeholder of the project. What should you do in this case?
Response:

A. Leave it as it is and allow automatic channel management to correct any issues. B. Advise the stakeholder that WLAN performance requirements will not be met and a new design process will be needed to meet the requirements. C. Increase the output power on all APs by 6 dB immediately. D. Remove all external antennas and use only the internal antennas to reduce multipath.

Discussion 0

Correct Answer: B Vote an answer

Question 8

When deploying a new WLAN infrastructure using Power over Ethernet (PoE) to power the access points (APs), you find that a known good AP is not powering up. You connect your laptop using the same cable without any issues. What is the most likely reason the AP did not power up?

A. Missing AP licenses on the controller B. Lack of PoE budget on the switch C. Layer 3 routing D. Spanning-tree convergence

Discussion 0

Correct Answer: B Vote an answer

Question 9

An engineering firm just upgraded their WLAN form nine 802.11n APS to nine 802.11ac APs. After this upgrade, they did not see any improvement in throughput. What is the most likely cause of this result?
Response:

A. The APs are still using the 5 GHz lower band B. APs are mounted on the wall C. APs are transmitting at a low transmit power D. The clients were not upgraded

Discussion 0

Correct Answer: D Vote an answer

Question 10

You have determined the best mounting locations for APs in a given installation. The facilities manager has asked you to change the locations for several APs due to aesthetic concerns. You suggest mounting the APs in the ideal locations and painting them so they go unnoticed in the environment.
What is a valid recommendation or consideration when painting APs?

A. Painting APs may void the product manufacturer's warranty. B. Always use paints with metallic dye in them to prevent potential RF propagation impact. C. Painting APs will significantly reduce the output power. D. Most AP models for indoor environments come in a variety of form factors and colors. Painting is never recommended.

Discussion 0

Correct Answer: A Vote an answer

Question 11

You are selecting external antennas for use in a bridge link deployment. What chart should you request from the antenna vendors to make an accurate selection?

A. mW to dBm conversion chart B. Elevation chart C. dBm to dB conversion chart D. Antenna coating chart

Discussion 0

Correct Answer: B Vote an answer

Question 12

Using a SCA means that all APs will be using the same channel in a given layer. How is the AP with which the client associates determined?
Response:

A. The client selects the AP based on a known set of MAC to BSSID mappings stored in the clients authorized SSID listing. B. All APs share a virtual BSSID. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client. C. All APs share a virtual Multicast Address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client. D. All APs share a virtual IP address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

Discussion 0

Correct Answer: A Vote an answer

Question 13

An organization has chosen to implement Wi-Fi 6E and operates in a regulatory domain allowing the use of all 6 GHz channels. Why can 40 MHz channels be used more easily in this network than one operating in the 5 GHz band?

A. Because ACI works differently in 6 GHz than in 5 GHz B. Because 6 GHz Wi-Fi uses Single Channel Architecture instead of Multiple Channel Architecture C. Because Wi-Fi 6E supports 40 MHz as a primary channel and ignores 20 MHz primary channels D. Because many more channels are available

Discussion 0

Correct Answer: D Vote an answer

CWNP Certified Wireless Design Professional - CWDP-305 Exam Practice Test