Cisco Implementing Cisco Service Provider Advanced Routing Solutions - 300-510 Exam Practice Test

Which attribute is used to instruct the router that packets must be processed by an ASA that is associated with the segment?

Refer to the exhibit. Router 1 resides in a different data center than Router 2 and Router 3.
Router 1 is running the IS-IS routing protocol, and it is preconfigured with LDP and segment routing. Which configuration must the engineer apply under router isis 111 on Router 1 to implement TI-LFA on the link to Router 2 without disrupting traffic to Router 3?

Refer to the exhibit. The network is situated at different locations on the customer site. The customer runs a mission-critical application behind CE2, which is connected over a 10 GB link to the local network of the customer. After recent configuration changes to the P and PE routers, an LSP failure has occurred, causing connectivity issues. CE1 is unable to reach the CE2 internal IP address.
Which action resolves this issue?

Refer to the exhibit. A regional service provider provides connectivity for a growing enterprise, which recently acquired a new location in a nearby city. The new location, which is connected at CE2. requires connectivity to the company's data center, which is connected to CE1. The service provider will use VPNv4 to connect the two locations. The networking team is planning to implement segment-routing traffic engineering to route traffic from PE1 to PE2 over a delay- optimized path through P2. Which action must the engineering team take to begin the implementation?

Refer to the exhibit. An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3.
Which mechanism should the engineer apply in order to steer the traffic correctly?

Refer to the exhibit. After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship.
Which reason for the problem is the most likely?

What is a requirement of PIM-SM?

Refer to the exhibit. Which LSA type is indicated by this router output?

SIMULATION
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks
Troubleshoot and configure OSPF according to the topology to achieve these goals:
1. R1 and R2 must not have OSPF BR/DR election over their E0/0 interfaces and must not advertise the OSPF host route for the OSPF connected neighbors.
2. E0/0 interfaces on R1 and R2 to be preferred over E0/1 interfaces for OSPF traffic. Only the numerical value of 15 is allowed.
3. Set the OSPF hello interval to 5 and the OSPF dead interval to 10 between R1 and R2 on interface E0/1.

An engineer is implementing LFA FRR on PE routers to allow unicast traffic to rapidly converge around link or node failures. The engineer configured IS-IS on the newly deployed routers in the data center in the same exchange as other routers. Which additional action must the engineer take before configuring LFA on the PE routers?

Refer to the exhibit. The service provider provides IPv6 connectivity to large enterprise customers with offices spanning several geographic regions SRv6 is running in the service provider core.
The service provider just signed a contract with a new customer that is still running IPv4. The new customer needs connectivity between its two sites connected via CE1 and CE2 and the internet.
Which action must the service provider s network-engineering team take to provide connectivity across the SRv6 data plane?

Drag and Drop Question
Drag and drop the features from the left into the order of operations for SRv6 SRH field creation and forwarding on the right.