300-410 by Cisco Actual Free Exam Q&As

Question 1

Refer to the exhibit. A network engineer is troubleshooting an AAA authentication issue for R1
from R2. When an engineer tries to open a telnet connection to R1 it opens the connection but
shows a %Authorization failed error message on the terminal and closes the connection silently.
Which action resolves the issue?

A. Configure authorization commands in the tacacs* server for the R1 router. B. Resolve tacacs+ server reachability from the R1 router. C. Resolve tacacs+ server host IP authentication miss configuration on the R1 router D. Configure the tacacs+ server host IP on the R1 router

Discussion 0

Correct Answer: A Vote an answer

Question 2

Which feature drops packets if the source address is not found in the snooping table?

A. IPv6 Source Guard B. IPv6 Prefix Guard C. Binding Table Recovery D. IPv6 Destination Guard

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 3

Refer to the exhibit. Packets arriving from source 209.165.200.215 must be sent with the
precedence bit set to 1, and packets arriving from source 209.165.200.216 must be sent with the
precedence bit set to 5. Which action resolves the issue?

A. set ip precedence critical in route-map Texas permit 20 B. set ip precedence immediate in route-map Texas permit 10 C. set ip precedence critical in route-map Texas permit 10 D. set ip precedence priority in route-map Texas permit 20

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 4

Which IP SLA operation can be used to simulate voice traffic on a network?

A. ICMP-echo B. UDP-jitter C. ICMP-jitter D. TCP connect

Discussion 0

Correct Answer: B Vote an answer

Question 5

Refer to the exhibit. Which action restores the routes from neighbors while still filtering
1.1.1.0/24?

A. Modify the route map to permit the access list instead of deny it B. Add a second line in the access list to permit any. C. Modify the access list to deny instead of permit it. D. Add a second sequence in the route map permit 20

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 6

Refer to the exhibit. The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host
192.168.10.10 cannot SSH to host 192.168.100.10 even though the flow is permitted.
Which action resolves the issue without opening full access to this router?

A. Temporarily remove the ACL from the interface to see if the flow works B. Run the show access-list FILTER command to view if the SSH entry has any hit statistic
associated with it C. Move the SSH entry to the beginning of the ACL D. Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow
works

Discussion 0

Correct Answer: C Vote an answer

Question 7

Refer to the exhibit. An administrator is setting up above shown routers to enable MVPN with
mGRE mode. What would be the recommended interface configuration that must be done by the
engineer to make it to work?

A. interface Tunnel0
description mGRE - DMVPN Tunnel
ip address 10.0.0.1 255.255.255.0
ip nhrp map multicast dynamic
ip nhrp network-id 1
tunnel source 10.0.0.1
tunnel mode IPSec multipoint B. interface Tunnel0
description mGRE - DMVPN Tunnel
ip address 10.0.0.1 255.255.255.0
ip nhrp map multicast dynamic
ip nhrp network-id 1
tunnel source 10.0.0.1
tunnel destination 172.17.0.2
tunnel mode IPsec multipoint C. interface Tunnel0
description mGRE - DMVPN Tunnel
ip address 10.0.0.1 255.255.255.0
ip nhrp map multicast dynamic
ip nhrp network-id 1
tunnel source 10.0.0.1
tunnel mode gre multipoint D. interface Tunnel0
description mGRE - DMVPN Tunnel
ip address 10.0.0.1 255.255.255.0
ip nhrp network-id 1
tunnel source 172.17.0.1
tunnel mode IPsec multipoint

Discussion 0

Correct Answer: C Vote an answer

Question 8

You have configured router R1 with multiple VRF's in order to support multiple customer VPN
networks. If you wanted to see the best path for the 10.1.1.0.24 route in VRF Blue, what
command would you use?

A. show ip route vrf Blue 10.1.1.0 B. show route all 10.1.1.0 C. show ip route 10.1.1.0 vrf Blue D. show ip route all 10.1.1.0

Discussion 0

Correct Answer: A Vote an answer

Question 9

Which two protocols work in the control plane of P routers across the MPLS cloud? (choose two)

A. LDP B. MPLS OAM C. LSP D. RSVP E. ECMP

Discussion 0

Correct Answer: A,D Vote an answer

Question 10

Refer to the exhibit. The Internet traffic should always prefer Site-A ISP-1 if the link and BGP
connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured
between BGP and OSPF routing protocols and it is not working as expected.
What action resolves the issue?

A. Set OSPF cost 200 at Site: A RTR1 and set OSPF Cost 100 at Site-B RTR2 B. Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2 C. Set OSPF cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2 D. Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2

Discussion 0

Correct Answer: B Vote an answer

Question 11

Refer to the exhibit. An engineer must redistribute networks 192.168.10.0/24 and
192.168.20.0/24 into OSPF from EIGRP. Where the metric must be added when traversing
through multiple hops to start an external route of 20. The engineer notices that the external
metric is fixed and does not add at each hop. Which configuration resolves the issue?

A. R2(config)#access-list 10 permit 192.168.10.0 0.0.0.255
R2(config)#access-list 10 permit 192.168.20.0 0.0.0.255 !
R2(config)#route-map RD permit 10
R2(config-route-map)#match ip address 10
R2(config-route-map)#set metric 20
R2(config-route-map)#set metric-type type-1 !
R2(config)#router ospf 10
R2(config-router)#redistribute eigrp 10 subnets route-map RD B. R1(config)#access-list 10 permit 192.168.10.0 0.0.0.255
(config)#access-list 10 permit 192.168.20.0 0.0.0.255 !
R1(config)#route-map RD permit 10
R1(config-route-map)#match ip address 10
R1(config-route-map)#set metric 20
R1(config-route-map)#set metric-type type-1 !
R1(config)#router ospf 10
R1(config-router)#redistribute eigrp 10 subnets route-map RD C. R2(config)#access-list 10 permit 192.168.10.0 0.0.0.255
R2(config)#access-list 10 permit 192.168.20.0 0.0.0.255 !
R2(config)#route-map RD permit 10
R2(config-route-map)#match ip address 10
R2(config-route-map)#set metric 20
R2(config-route-map)#set metric-type type-2 !
R2(config)#router ospf 10
R2(confjg-router)#redistribute eigrp 10 subnets route-map RD D. R1(config)#access-list 10 permit 192.168.10.0 0.0.0.255
R1(config)#access-list 10 permit 192.168.20.0 0.0.0.255 !
R1(config)#route-map RD permit 10
R1(config-route-map)#match ip address 10
R1(config-route-map)#set metric 20
R1(config-route-map)#set metric-type type-2 !
R1(config)#router ospf 10
R1(config-router)#redistribute eigrp 10 subnets route-map RD

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Cisco Implementing Cisco Enterprise Advanced Routing and Services - 300-410 Exam Practice Test