Contact Us
FAQ's
Login / Register

Home
FORUM
All Vendors
Guarantee
Testimonials
Cart (0)

Pure Storage Certified FlashArray Implementation Specialist - FlashArray-Implementation-Specialist Exam Practice Test

Page: 1 / 20
Total 236 questions

Please signup / login to view this exam, then you will be able to view the entire exam for free.

Get Full Access Now

Question 1

An Implementation Engineer has completed a hardware NDU, but after the upgrade, Purity reports a "health not responding" status when running pureadm status.
Before contacting support, which command should the Implementation Engineer run to review a list of possible logged issues?

A. purehw diagnose --verbose B. puremessage list --open --hidden C. purearray diagnose --log D. purealert watcher list --live

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 2

Prior to running the puresetup newarray command, which command should an Implementation Engineer run on a new install of a FlashArray//XR4 array?

A. hardware_check.py B. purehw list C. pureboot list D. cobalt_check.py

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 3

A customer needs to have arrays installed and configured with ActiveCluster and ETH replication. The installation document contains 3 IP addresses. How many additional IP addresses are needed?

A. 4 B. 6 C. 5

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 4

During a hardware NDU from a FlashArray//X20R3 to an X20R4-LL (low-line) model, the Implementation Engineer encounters a failure during the power supply check. Voltage readings are correct.
What is a likely cause of this failure?

A. There are more than 10 drives installed in the chassis. B. The facility power is providing 208V instead of 120V. C. Purity does NOT recognize the power supplies installed in the array. D. The power cables are NOT fully seated in the array.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 5

An Implementation Engineer is performing a capacity consolidation on an X50R3.
Which command is needed for the engineer to determine whether the customer's FlashArray supports SAS Flash Modules?

A. puredrive list --total --type controller B. purehw list --type controller --all C. purehw list --type drive --all

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 6

An Implementation Engineer is performing a FlashArray//XR4 to FlashArray//XL upgrade, and is preparing to remove the XR4 CT0 controller.
Which command should the Implementation Engineer run to stop Purity after confirming CT0 is the secondary controller?

A. purehw controller stop --verify-array ARRAY_NAME ct0 B. purewes controller disable --purity --verify-mode secondary --verify-array ARRAY_NAME ct0 C. purewes controller setattr --disable --verify-mode secondary --verify-array ARRAY_NAME ct0 D. purewes controller disable --purity --verify-mode primary --verify-array ARRAY_NAME ct0

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 7

During a FlashArray//XR5 upgrade, when should the Implementation Engineer run start_ndu controller-ndu to set the HWNDU specific tunable?

A. After Purity has been installed on the new //XR5 controller and before it has been initialized. B. After the new //XR5 controller has been initialized and before initiating the controller failover. C. Before installing Purity on the new //XR5 controller. D. After the power supply units have been replaced and before stopping Purity on CT0.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 8

An Implementation Engineer is replacing a failing component in a FlashArray//XR4 and must ensure proper service clearance at the front and rear of the array.
What is the required service depth clearance for the front and rear panels of the FlashArray//XR4?

A. Front panel: 216 mm (8.5 in.), Rear panel: 530 mm (20.9 in.) B. Front panel: 530 mm (20.9 in.), Rear panel: 530 mm (20.9 in.) C. Front panel: 530 mm (20.9 in.), Rear panel: 216 mm (8.5 in.) D. Front panel: 216 mm (8.5 in.), Rear panel: 216 mm (8.5 in.)

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 9

During an intra-series upgrade from //XR3 to //XR4, which command should the Implementation Engineer run to verify host connectivity before removing the secondary controller?

A. purehost list --hostless B. iobalance --sampletime 30 C. host_connectivity --hosts

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 10

A FlashArray//XR2/3 has an Ethernet mezzanine (EMEZZ), what are the interface names of the ports on the mezzanine?

A. ETH6, ETH7, ETH8, and ETH9 B. ETH8, ETH9, ETH10, and ETH11 C. ETH10, ETH11, ETH12, and ETH13

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 11

What is the rack unit height of a FlashArray//XR2/3?

A. 3 B. 4 C. 5

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Question 12

For a new FlashArray installation, a customer's network team has NOT provisioned network ports for management connectivity. How Will this affect the installation process?

A. The customer Will be unable to login to the array. B. The array's data will be inaccessible. C. Management connectivity is required for installation.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for PassTestking members. You can sign-up / login (it's free).

Page: 1 / 20
Total 236 questions

Unlock all FlashArray-Implementation-Specialist features

No captcha needed
365 Days Free Updates
Set your Desired Pass Percentage
Allocate Time (Hours : Minutes)
Two Modes For FlashArray-Implementation-Specialist Practice
Customer Support

Get Full Access Now

Get in Touch

PassTestking

Our Exam Dumps will provide you with the free demo before you purchase. Our Practice Questions can help you improve your professional ability. Our Study Material provide you with excellent prepare materials for you to pass the exam and get the certification.

Latest Practice Tests

1Z0-1054-26 Practice Test
312-49 Practice Test
3V0-21.25 Practice Test
CTFL_Syll_4.0 Practice Test
C_S4TM_2601 Practice Test
H12-821_V1.0 Practice Test

Useful Links

All Products
FAQs
Privacy Policy
Guarantee & Refund Policy
Terms & Conditions
How to buy?
About Us

Contact Us

Our Working Time: ( GMT 0:00-15:00 )
From Monday to Saturday

Support: Contact now

If you have any question please leave me your email address, we will reply and send email to you in 12 hours.

Copyright © 2026 PASSTESTKING.COM. All rights reserved. All trademarks are the property of their respective owners and we don't provide actual questions from any vendor.